Top 10 Best Control 4 Pin Fans 2023 – Complete Buying Guide

Features :

• Expand 4-pin fan interfaces, solving the problem of lack of motherboard fan interfaces. Designed for 12V 4-Pin 3-Pin fans, support simultaneous starting at most 10 channel fans.
• In the hub interfaces, the RED CPU interface is the CPU fan dedicated interface (with speed detection function). Since the mainboard can only receive one rotation speed signal, the remaining nine conventional fan interfaces have the PWM function, but no speed signal.
• For both 4-Pin and 3-Pin fans. Please note 4Pin fan speed can be adjusted by temperature control. 3Pin fan can also be used, but because 3Pin has no PWM function, it is at fixed speed after inserting.
• There is EVA double-sided adhesive at the back of the hub, which can be easily affixed to a flat place. Also a fixing screw hole in the middle of the PCB to facilitate fixing to a part of the chassis.
• RED is expected to be a pass through for the CPU fan. So, the hub has a power source fed from the computer power supply, then the speed is regulated by the speed for the “source” fan. You can connect to the CPU fan lead on the system board or the chassis fan lead. The ten fans will spin at the same speed, that designated by the system for that fan. If the chassis fan is configured in BIOS to run at 50%, you will have 10 fans at 50%.

Features :

• Supports all internal 12V 5A fans, synchronous rectified output, high efficiency, no need for additional heat sinks even for high current operation.
• Multiple fans can be used in parallel (total current does not exceed 5A), support automatic temperature control and air cooling speed control, temperature control speed has four temperature zone settings, widely used.
• It can be turned on with the three-wire fan monitoring function (stall warning).
• Circuit load capacity: 5A for each output and 8A for bus current.
• Output range: 20%-100% for the first channel, or 40%-100% for the first channel (TFL = ON), 10%-100% for the second channel and the third channel. (Note: The above range is only applicable to the PWM range, the actual control effect will vary depending on the fan)

Features :

• -MOST EFFICIENT SATA TO FAN ADAPTER IN 2020✔ Managing multiple fans from a single case input has become easier for you now. If your motherboard lacks fan interfaces, use this neat & tidy way to add fans & expand fan interfaces designed for 12 V 4-pin fan. This PWM hub SATA accurately controls fan speed, you can slow down & speed up the fans up to the maximum speed. You need to connect the SATA & the 4 pin at the same time to run multiple fans.
• -PWM FAN CONTROLLER TEMPERATURE CONTROL✔ The CPU Port (red port), would be the only port that can be controlled by the operating system. The other 9 black fan ports CAN NOT be adjusted in speed and will copy the power level of what the red port is at. Please note 4 Pin fan speed can be adjusted by temperature control as well. 3 Pin fans may also be used but have no PWM function and will stay at it’s fixed speed after inserting.
• -INSTALLATION & CONFIGURATION✔ Simple installation & easy configuration, this fan splitter will work even if only connected to the PSU with SATA connector. You just plug the board into the CPU fan motherboard connection & then SATA for power. It has EVA double-sided adhesive tape at the back of the hub to mount to the case or any flat place. You can fix the screw hole in the middle of the PCB to facilitate fixing to a part of the chassis.
• -STEP BY STEP SET-UP✔ You will receive 1 hub & 1 PWM connector in your package. The PWM interface is connected to CPU fan interface on motherboard by PWM cable & the red interface is dedicated for CPU fan. Connect 1 fan to the red port on fan hub then connect remaining fans. You then need to connect the fan hub’s PWM cable to the motherboard. Connect the power supply SATA cable to fan hub before you attach/stick it on the chassis.
• -MONEY BACK PRODUCT WARRANTY✔ Our product is backed up by manufacturer’s warranty so feel free to contact us for any query or information. We have a track record of ensuring happiness of clients and are absolutely confident that our product will exceed your expectations. Just in case the product falls short of your expectations in any manner, you can return it for a 100% refund. We will go an extra mile to redress the situation at hand.

Features :

• If 3-pin non-PWM fans are connected to this fan hub, this fan hub CANNOT give them extra PWM function. They will run at FULL SPEED.
• If 4-pin PWM fans are connected to this fan hub, DUTY RATIO of all PWM fans can be adjusted at the same time. That is, all PWM fans will run at the same DUTY RATIO. Only speed of Fan 1 can be identified by the system.
• Capable of connecting to 10 PC fans simultaneously for cooling the computer system.
• Powered by a stable SATA connection to the system PSU for up to 10 fans.
• Velcro and screw mountings applicable for the tower interiors.

Features :

• motherboard 4-pin interface, PWM speed control, can be used for multiple cooling fans, expansion and expansion motherboard 4 pin interface, suitable for CPU or computer chassis fan.
• fans can be used for 12V DC, or for fixed Molex voltage operation of 5V DC (only 2-pin connector required) cable compatible with standard 3-pin fan
• power supplies for four 3-pin or 4-pin (PWM connector) PC chassis fans with 4-pin Molex connectors
• fan splitter cable provides more fans and increases airflow inside the computer case
• adapter cable length 16 cm / 6.5 inches. (2 pieces) This product has been upgraded and updated. The performance of the new product is more stable, the connector is upgraded, the old connector, the new connector, and universal! The length of the new products has been shortened. New line length: 12.5 cm/5 inches

Features :

• Excellent 1 to 5 splitter 5 way 4-Pin PWM fan power supply extension cable cord, better power supply for PC computer case internal motherboard fans.
• Widely Compatible: support 4-Pin and 3-Pin fans cable, the 1 to 5 splitter 5 way fan power extension cable compatible with 4-Pin and 3-Pin PC case motherboard fans.
• Black sleeved nylon braided cable, more durable and make the internal of pc case looks more clean & tidy.
• Plug-n-Play and easy to plug, 5 way 4-Pin male connector jack fan hub cable.
• The extension cable offers greater flexibility between motherboard and CPU cooling fans. Only the “CPU” port can be read the speed.

Features :

• RGB Lighting: Signature cooling performance with an RGB design: a perfect choice for all of the users wanting lighting effects that are fully customizable
• New Blade Design: Revised curve blade design to improve airflow and air pressure. A refreshed blade for improved lighting
• Enhanced Fan Frame: Enhanced frame structure, reducing turbulent flow noise increase efficiency
• Sealed Bearing Structure: Sealed and secured fan bearing, preventing dust and lubricating oil leakage while increasing the fan’s operation stability and life span

Features :

• ✔MOST EFFICIENT SATA TO FAN ADAPTER IN 2019✔ Managing multiple fans from a single case input has become easier for you now. If your motherboard lacks fan interfaces, use this neat & tidy way to add fans & expand fan interfaces designed for 12 V 4-pin fan. This PWM hub SATA accurately controls fan speed, you can slow down & speed up the fans up to the maximum speed. You need to connect the SATA & the 4 pin at the same time to run multiple fans.
• ✔PWM FAN CONTROLLER TEMPERATURE CONTROL✔ The CPU Port (red port), would be the only port that can be controlled by the operating system. The other 9 black fan ports CAN NOT be adjusted in speed and will copy the power level of what the red port is at. Please note 4 Pin fan speed can be adjusted by temperature control as well. 3 Pin fans may also be used but have no PWM function and will stay at it’s fixed speed after inserting.
• ✔INSTALLATION & CONFIGURATION✔ Simple installation & easy configuration, this fan splitter will work even if only connected to the PSU with SATA connector. You just plug the board into the CPU fan motherboard connection & then SATA for power. It has EVA double-sided adhesive tape at the back of the hub to mount to the case or any flat place. You can fix the screw hole in the middle of the PCB to facilitate fixing to a part of the chassis.
• ✔STEP BY STEP SET-UP✔ You will receive 1 hub & 1 PWM connector in your package. The PWM interface is connected to CPU fan interface on motherboard by PWM cable & the red interface is dedicated for CPU fan. Connect 1 fan to the red port on fan hub then connect remaining fans. You then need to connect the fan hub’s PWM cable to the motherboard. Connect the power supply SATA cable to fan hub before you attach/stick it on the chassis.
• ✔MONEY BACK PRODUCT WARRANTY✔ Our product is backed up by manufacturer’s warranty so feel free to contact us for any query or information. We have a track record of ensuring happiness of clients and are absolutely confident that our product will exceed your expectations. Just in case the product falls short of your expectations in any manner, you can return it for a 100% refund. We will go an extra mile to redress the situation at hand.

Features :

• Black sleeved 4 way PWM splitter hub for computer fans
• Designed for the need to control numerous system fans
• Capable of expanding one motherboard PWM fan header to support up to four fans
• Support PWM Function, Speed control, satisfy your control needs
• Compatible with 3-pin / 4-pin Fans

Features :

• This 4-Pin Adapter Cable Allows You To Connect Stock GPU Fans And Pumps To An External Fan Connector
• Mini 4-Pin Connection Is Found On Most Graphics Card Fans And Pumps (For Built-In Liquid Cooling Models)
• Wired To Support RPM Monitoring And PWM Fan Speed Control
• All Black Appearance Featuring Black Connectors And High Density Black Sleeving
• Cable Length (Excluding Connectors) 12″/30cm